Home > Hot Tub > Hot Tub Error Code Hh

Hot Tub Error Code Hh

Contents

Changed both sensors and still getting HH warning. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. Blocked Skimmer.4. Spa is shut down. http://indowebglobal.com/hot-tub/hot-tub-error-code-sl.html

See M7 Sensors here. Select "Message Other than CrC or CHKSUM FAIL" Below. If he kisses you, then he might like you. The M-7 should detect a bad sensor and display a SN error so it isn't likely a bad sensor. http://en.allexperts.com/q/Hot-Tubs-3536/2010/2/viking-spa-HH-error.htm

Cal Spa Hh Error Code

I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Thanks.? The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2.

I have a CALSPA hot tube Add your answer Source Submit Cancel Report Abuse I think this question violates the Community Guidelines Chat or rant, adult content, spam, insulting other members,show In most cases, for newer spas anyway, the water flow problem can be quickly remedied and the spa will cool, reset and start again on it's own. Doing so may cause damage to the pump and cause the system to go into an overheat condition.If after repeated attempts (hours apart) you still cannot get all pumps to prime, Cal Spa Error Codes So before pressing any buttons, verify that water is flowing from the circ pump outlet.

Dream Maker Control Systems for Spas or Hot Tubs: OH = Overheat 108° F, spa is deactivated. The sensor that is plugged into the sensor “A” or “B” jack is not working. Our Privacy Policy has details and opt-out info. news Blocked Suction Fitting.3.

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected. What Does Hh Mean On A Hot Tub In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. Spa has shut down. Observe the panel display as you do this.

Hot Tub Error Code Oh

Read our FAQ! http://www.poolspaforum.com/forum/index.php?/topic/27194-hh-and-oh-warnings/ Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions. Cal Spa Hh Error Code Touch any button to reset the system. Balboa Hot Tub Error Codes If the system starts up, runs fine and heats in standard mode for a while before erroring, is the water temperature in the spa actually getting past 104 degrees (F)?

Rare system error. check over here Test and Reset the G.F.C.I. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different. Try Turning the Power OFF and back ON again, or contact your Dealer or Service Organization.1. Hot Tub Overheating Troubleshooting

The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat. Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? his comment is here Still faulting to HH. $210.00 just for a service visit.

In rare cases (usually warmer climates), the circulation pump may also cause overheating. Cal Spa Oh Code Contact qualified service technician. Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then.

Tried cleaning filter per advice of company I bought it from and still got warning.

The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the Press any button to reset or wait 15 minutes and spa will automatically reset. Both are secured with black plastic nut around the gray cable. Sn Code On Hot Tub Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

For spas without digital controls, you may need to manually reset the high limit switch near the heater housing. Currently authorized to perform warranty work on Cal Spa products.Education/CredentialsEight years of radar electronics training in the Air Force. ICE = Freeze condition. 55°F detected. http://indowebglobal.com/hot-tub/hot-tub-error-code-5n.html Send Share This Copyright © 2016.

Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. Refill, if necessary. Back to Top rCH or NEW FILTER Message Time to "Change Filter Reminder" (rCH)Appears Every 365 Days*. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). Back to Top HOt or HOT-CALL SVC Message A Pump appears to have been stuck ON before a GFCI trip, causing an extreme overheat.If the extreme overheat conditions are determined, a

Back to Top rdr or DRAIN WATER Message Time to "Drain Spa Water Reminder" (rdr).Appears Every 90 Days*. Press "Mode" Button to Clear Message. Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. Pictured here is a Balboa® control system used in Belize Spas brand.

The causes of low water flow in a spa include: Dirty spa filter cartridge Closed or partially closed valves or jets Pump has an air lock, or has lost prime Low Contact ACC. Leave a Reply Click here to cancel reply.