Home > Hot Tub > Hot Tub Error Code 5n

Hot Tub Error Code 5n

Contents

Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. I'm still at a loss. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... http://indowebglobal.com/hot-tub/hot-tub-error-code-sl.html

Am I running in circles? I heard that with the switchs disconnected, the spa should run, but mine does not. Right. ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill).

Balboa Hot Tub Error Codes

Make sure that all jets are open, and nothing is blocking the spa drain cover flow. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Sign in 2 0 Don't like this video?

There also could be a voltage problem, excessive voltage creates heat. In Economy or Sleep mode, the pump may be off for hours outside a filter cycle. Try unplugging topside and plugging into another port. How To Fix Flo Error Hot Tub I started probing around with my multimeter and when I touched the probe ends to the safety switch, "the relay looking device with the blue cover over it located on the

Do not enter the spa. How To Fix Sn Code On Hot Tub Make sure that all jets are open, and nothing is blocking the spa drain cover flow. I don't know if this is normal because I do not have the tech specs. news These will present themselves in many forms on the display, such as Sn, Sn1, Sn2, and they refer to temperature sensors located on the heater manifold.

I also tried pressing the temp controls with no luck. Marquis Spa Error Codes or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products This could indicate a flow problem. These will present themselves in many forms on the display, such as Sn, Sn1, Sn2, and they refer to temperature sensors located on the heater manifold.

How To Fix Sn Code On Hot Tub

Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question.

If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. Balboa Hot Tub Error Codes Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp Vita Spa Error Codes Contact Us My Account My Cart Log In Site Index Home Page MSP Rewards Contact Us Win Free Chemicals Owners Manuals Master Spas Care Guide Error Codes Policies & FAQ’s Review

First Name: Last Name: Email: Sign Up Jump to content Portable Hot Tubs & Spas Existing user? this content Same Day Shipping on most orders placed before 3pm CST Free Shipping on orders over $99 (855) 308-2149 00 : 00 : 00 (Hours) OPEN 7 DAYS A WEEK Master SpasLegend Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa OH = Over heat. Balboa Hot Tub Codes Sl

SnS Sensors are out of balance. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. I started probing around with my multimeter and when I touched the probe ends to the safety switch, "the relay looking device with the blue cover over it located on the weblink I had a new pump installed last weekend and everything worked just fine.

Or, it could be a problem with the thermostat allowing the heater element overheat. Great Lakes Hot Tub Error Codes FL1 = Water flow problem, inhibited or pressure switch malfunction. drops.

For the error messages of HFL, LF, Dr, or DRY.

Rafken SpaRepair 993 views 2:57 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09. The sensor that is plugged into the Sensor “A” jack is not working. If water is not flowing through the heater chamber fast enough, it gets too hot, and the safety high temp sensors go into action - just doing their job. Great Lakes Hot Tub Troubleshooting Your hot tub does NOT heat during this time in this mode.

The next morning the SN code was back and the tub was off. Shop By Categories Accessories Air Controls Chemicals Spa Boss Cleaners Spa Boss Sanitizers SpaBoss Water Balancers Spa Crystals Fragrances Circuit Boards Control Packs Covers Clarity Spa Covers Down East Spa Covers Heater is shut down, but other spa functions run normally. check over here FL2 = Pressure switch problem.

At 107°F the spa should reset. I had a new pump installed last weekend and everything worked just fine. Heater disabled but the spa is operational. I also tried pressing the temp controls with no luck.

You must have JavaScript enabled in your browser to utilize the functionality of this website. My owners manual confirms that the spa will be disabled if the Sn code displays. It keeps breaking right away. All rights reserved.

Clean or replace your spa filter cartridge as a first step. Heater is deactivated. That is the overheat sensor. Ike Indoor 20x40 35,000 gallon vinyl pool with 1.5 HP 2 speed Jandy FloPro pump, Hayward EC75 Perflex DE filter, 11 4x12 Techno-Solis solar panels w/ Aquasolar controller, Aquabot Turbo T

I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address Heater disabled but the spa is operational. Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa OH = High temperature condition, has reached 110°F.

If the problem continues make sure circulation pump is moving water. If you check the stainless steel heater vessel you'll find a slot with a grey wire tucked inside. Rating is available when the video has been rented. I started probing around with my multimeter and when I touched the probe ends to the safety switch, "the relay looking device with the blue cover over it located on the

These are similar to the Sn1 and Sn2 codes, signaled from the high limit or water temperature sensors.