Home > Harley Davidson > Harley Davidson Error Code P1001

Harley Davidson Error Code P1001

Contents

Wherever it came from and whoever contributed, thank you. Harley Davidson Check Engine Lamp - The check engine lamp indicates the ignition control module (ICM) has determined a fault condition exists. To diagnose Harley Davidson system problems, begin by observing the behavior of the check engine lamp. All Harley Davidson System Problems - Fall into at least one of three general categories: Harley Davidson No Start - The engine cranks over freely, but will not start. Source

The rigid… Read more » Watch Now >> 22:03 Harley-Davidson® Clutch Removal on a Sportster You might be used to adjusting your Harley Davidson clutch but mileage and riding style can U1064 Loss of TSM/FSFM Serial Data to ECM 7. You can replace with stock… Read more » Watch Now >> 9:09 Custom Harley-Davidson® Exhaust Installation Part 2 Here's where the number one upgrade performed on almost every Harley-Davidson can go Turning the ignition key to OFF stores the new PIN in the module.

Harley Diagnostic Trouble Codes

The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. Performance Cams Proven performance for any build. Harley Davidson engine cranks but will not start - Is there fresh fuel in tank? Turn OFF the ignition switch.

Tailgunner1: I DO NOT have the original PIN, I was attempting to impliment the reset procedure, but can't get the bike to respond using the procedure described in my original post. The length of time the lamp is illuminated and the length of time in which it is off are each about 0.5 second in duration. P1357 Front Cylinder Combustion Intermittent 56. Harley Davidson Diagnostic Code Reader This condition is normal and does not by itself indicate a malfunction.

The word “diag” should then appear. 4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing. 5 - Each letter Human Verification In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). 1- Turn Ignition switch to OFF & Run/Stop switch is to http://www.1130cc.com/forums/showthread.php?t=381642 The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage.

This page was generated at 02:52 AM. Sportster Diagnostic Codes In this manner, there may sometimes be a false indication of the current DTC. P0220 TPS2 Range Error 31. EFI Tuning See More EFI Tuning Dynojet Power Vision The fastest ECM flash tuner on the market while also offering the most powerful tuning features.

Harley Davidson Code List

Other models will be under the seat. a fantastic read P0572 Brake Switch Low 47. Harley Diagnostic Trouble Codes Home position established by taking readings off the 22 teeth on the alternator rotor. How To Clear Codes On Harley Davidson For example, a problem with the ignition coil will be considered a current fault even after the problem is corrected, since the ignition control module will not know of its resolution

P0262 Front Injector High 60. this contact form My 09 nightster recently started having intermittent start issues and now will not start at all. or www.fuelmotousa.com hold no responsibility either implied or otherwise for mechanical, electrical or other failure when using any aftermarket performance product. There are additional codes for the 08 bikes not listed here but are listed in this same section in another post. Harley Bcm Codes

The time now is 02:52 AM.

-- V-twin new ---- V-Twin Alternate Style Contact Us - V-Twin Forum : Harley-Davidson Forums - Archive - Privacy Statement - Top The manifold absolute pressure sensor is supplied 5 volts from the ignition control module and sends a signal back to the ignition control module. blackfxsts Electrical/Lighting/Alarm 2 07-29-2011 10:27 PM Need help.... have a peek here I think, "It is better to drink this beer and let their dreams come true than be selfish and worry about my liver." - Babe Ruth Tailgunner1 is online now

Check in the electrical section stickys for code procedures . Codes For Harley Davidson Models Fuelpak FP3 Available for Harley-Davidson models which utilizes the CAN Bus HDLAN ECM. Fuel Moto Speed Shop See the Fuel Moto Speed Shop Big Bore Kits / Crate Engines We have spend years testing and developing our big bore kits so you don't have

or Log In Log In Forums General Harley Davidson ForumsNew Members AreaNewsletter ArchiveGeneral Harley Davidson ChatThe General B/S ForumHarley Davidson VideosOff Topic VideosHDForums MascotRoad TripsMotorcycle Insurance DiscussionForum IssuesTesting AreaHarley Davidson MotorcyclesSoftail

Thanks The service manual is very carefully written so that you will never find this information.. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes Jackpot Exhaust The leader in quality and performance. Harley Davidson Check Engine Light The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.

Sensor also controls the cooling fan relay that provides 12 Vdc to the fans. B1142 Smart Security System Internal Fault 6. P1352 Front Ignition Coil Driver High/Shorted 54. http://indowebglobal.com/harley-davidson/harley-davidson-error-code-p0374.html To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.) P

DTC – Diagnostic Trouble Codes ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & P2103 EFI Motor Circuit High 41.