Home > Error Code > Hot Tube Error Codes

Hot Tube Error Codes


HL High limit switch tripped. If you are unsure of something or have any questions, please do not hesitate to contact us via Email. For Low Flow spa error codes, check the filter, check the pump and check the valves to find something that is obstructing the water flow. DO NOT ENTER THE WATER! navigate here

The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. If you still have problems, check over your temp sensor and hi limit circuits for wire or plug or sensor problems. You must be logged in to post a comment. Spa has shut down OHS Overheat. a fantastic read

Balboa Hot Tub Error Codes

All Rights Reserved. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. Pr When spa is first actuated, it will go into Priming Mode. Sensor plugged into jack B is not working.

Sn3 Open or shorted sensor ( heater disabled). Std Spa operating in Standard Mode. Water temperature has reached 118ºF. Coleman Spa Error Codes Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog".

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. Leave a Reply Click here to cancel reply. See M7 Sensors here. https://spacare.com/spasideerrorcodes.aspx Shut the spa down, remove the filter and make sure all the jets are open.

LF Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). Hot Tub Error Code Oh Check for proper spa water level and ensure pump is primed. Following is a listing of all the possible messages along with their meanings. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Vita Spa Error Codes

drops.HL = High limit switch tripped. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ If you need assistance with spa trouble codes, you can call us anytime at 800-770-0292  Happy Hot Tubbin' Daniel Lara Hot Tub Works Tags: hot tub error code, Balboa Hot Tub Error Codes Topside controls also give lots of information about your spa status, which are not to be confused with spa error codes. Marquis Spa Error Codes Spa has shut down OP Open circuit sensor P1, P2 or P3-ER Pump 1,2 or 3 error or failure pd Power supply interrupted, unit running on battery backup PnL Panel error;

SESH Sensor short, nonfunctional. http://indowebglobal.com/error-code/honeywell-error-codes.html The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition. Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when If tripping continues, call for service.• Deactivate spa lock Hercules Control Systems for Spas or Hot Tubs: OH = Spa temp exceeds acceptable limits FLO = Flow problem ICE = Freeze How To Fix Flo Error Hot Tub

FL Spa water is more than 20° F cooler than the temperature set point. Should the power return to normal, the PF error will reset itself. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. http://indowebglobal.com/error-code/hot-tub-error-codes-fl1.html One sensor has detected 118º F.

F2 Panel sensors have been pressed too many times in a short period of time. Gecko Spa Pack Error Codes Heater is deactivated. Sn2 Nonfunctional temperature sensor.

When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases.

You can leave a response, or trackback from your own site. Make sure that all jets are open, and nothing is blocking the spa drain cover flow. Quick View HOT TUB SUPPLY SUPERSTORE 1-800-770-0292 Sunday - Saturday7am - 7pm CST Customer Care | About Us | Contact Us | Track Your Order | Shopping Cart | Login Coast Spa Error Codes The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes.

Spa has shut down. PSoL Pressure switch open with low pump. Pressure switch is not working.SN = Non functional high temperature sensor. weblink Clean or replace the spa filter, open all the jets and turn the pump on high.

Heater is deactivated. Std Spa operating in Standard Mode.